mirror of
git://git.code.sf.net/p/openocd/code
synced 2025-07-24 05:59:49 +10:00
This should allow to share common configs for both regular access and high-level adapters. Use the newly-added functionality in stlink and icdi drivers, amend the configs accordingly. Runtime-tested with a TI tm4c123g board. Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad Signed-off-by: Paul Fertser <fercerpav@gmail.com> [gus@projectgus.com: context-specific deprecation warnings] Signed-off-by: Angus Gratton <gus@projectgus.com> [andrew.smirnov@gmail.com: additional nrf51.cfg mods] Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com> Reviewed-on: http://openocd.zylin.com/1664 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
70 lines
1.8 KiB
INI
70 lines
1.8 KiB
INI
#
|
|
# Freescale Kinetis KL25 devices
|
|
#
|
|
|
|
#
|
|
# KL25 devices support both JTAG and SWD transports.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME kl25
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 4kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x1000
|
|
}
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x0bc11477
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_CHIPNAME.cpu
|
|
|
|
# It is important that "kinetis mdm check_security" is called for
|
|
# 'examine-end' event and not 'eximine-start'. Calling it in 'examine-start'
|
|
# causes "kinetis mdm check_security" to fail the first time openocd
|
|
# calls it when it tries to connect after the CPU has been power-cycled.
|
|
$_CHIPNAME.cpu configure -event examine-end {
|
|
kinetis mdm check_security
|
|
}
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME kinetis 0 0 0 0 $_TARGETNAME
|
|
|
|
# Table 5-1. Clock Summary of KL25 Sub-Family Reference Manual
|
|
# specifies up to 1MHz for VLPR mode.
|
|
adapter_khz 1000
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# Table 5-1. Clock Summary of KL25 Sub-Family Reference Manual
|
|
# specifies up to 24MHz for run mode; Table 17 of Sub-Family Data
|
|
# Sheet rev4 lists 25MHz as the maximum frequency.
|
|
adapter_khz 24000
|
|
}
|