mirror of
git://git.code.sf.net/p/openocd/code
synced 2025-07-23 21:11:55 +10:00
751e2454bf
Atmel introduced a "Device Service Unit" (DSU) that holds the CPU in reset if TCK is low when srst (RESET_N) is deasserted. Function is similar to SMAP in ATSAM4L, see http://openocd.zylin.com/2604 Atmel's EDBG adapter handles DSU reset correctly without this change. An ordinary SWD adapter leaves TCK in its default state, low. So without this change any use of sysresetreq or srst locks the chip in reset state until power is cycled. A new function dsu_reset_deassert is called as reset-deassert-post event handler. It optionally prepares reset vector catch and DSU reset is released then. Additionally SWD clock comment is fixed in at91samdXX.cfg and clock is lowered a bit to ensure a margin for RC oscillator frequency deviation. adapter_nsrst_delay 100 is commented out because is no more necessary after http://openocd.zylin.com/2601 Change-Id: I42e99b1b245f766616c0a0d939f60612c29bd16c Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/2778 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
88 lines
2.6 KiB
INI
88 lines
2.6 KiB
INI
#
|
||
# script for Atmel SAMD, SAMR, SAML or SAMC, a CORTEX-M0 chip
|
||
#
|
||
|
||
#
|
||
# samdXX devices only support SWD transports.
|
||
#
|
||
source [find target/swj-dp.tcl]
|
||
|
||
if { [info exists CHIPNAME] } {
|
||
set _CHIPNAME $CHIPNAME
|
||
} else {
|
||
set _CHIPNAME at91samd
|
||
}
|
||
|
||
if { [info exists ENDIAN] } {
|
||
set _ENDIAN $ENDIAN
|
||
} else {
|
||
set _ENDIAN little
|
||
}
|
||
|
||
# Work-area is a space in RAM used for flash programming
|
||
# By default use 2kB
|
||
if { [info exists WORKAREASIZE] } {
|
||
set _WORKAREASIZE $WORKAREASIZE
|
||
} else {
|
||
set _WORKAREASIZE 0x800
|
||
}
|
||
|
||
if { [info exists CPUTAPID] } {
|
||
set _CPUTAPID $CPUTAPID
|
||
} else {
|
||
set _CPUTAPID 0x4ba00477
|
||
}
|
||
|
||
swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
|
||
|
||
set _TARGETNAME $_CHIPNAME.cpu
|
||
target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
|
||
|
||
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
||
|
||
# SAMD DSU will hold the CPU in reset if TCK is low when RESET_N
|
||
# deasserts (see datasheet Atmel-42181E–SAM-D21_Datasheet–02/2015, section 12.6.2)
|
||
#
|
||
# dsu_reset_deassert configures whether we want to run or halt out of reset,
|
||
# then instruct the DSU to let us out of reset.
|
||
$_TARGETNAME configure -event reset-deassert-post {
|
||
at91samd dsu_reset_deassert
|
||
}
|
||
|
||
# SRST (wired to RESET_N) resets debug circuitry
|
||
# srst_pulls_trst is not configured here to avoid an error raised in reset halt
|
||
reset_config srst_gates_jtag
|
||
|
||
# Atmel's EDBG (on-board cmsis-dap adapter of Xplained kits) cannot
|
||
# stop the MCU before it starts executing code if hardware RESETN
|
||
# line is configured by command "reset_config srst_only"
|
||
# Use "reset_config none" (default) before flash programming.
|
||
|
||
# Do not use a reset button with other SWD adapter than Atmel's EDBG.
|
||
# DSU usually locks MCU in reset state until you issue a reset command
|
||
# in OpenOCD.
|
||
|
||
# SAMD runs at SYSCLK = 1 MHz divided from RC oscillator after reset.
|
||
# Other members of family usually use SYSCLK = 4 MHz after reset.
|
||
# Datasheet does not specify SYSCLK to SWD clock ratio.
|
||
# Usually used SYSCLK/6 is slow, testing shows that debugging can
|
||
# work @ SYSCLK/2 but your mileage may vary.
|
||
# This limit is most probably imposed by incorrectly handled SWD WAIT
|
||
# on some SWD adapters.
|
||
|
||
adapter_khz 400
|
||
|
||
# Atmel's EDBG (on-board cmsis-dap adapter of Xplained kits) works
|
||
# without problem at maximal clock speed. Atmel recommends
|
||
# adapter speed less than 10 * CPU clock.
|
||
# adapter_khz 5000
|
||
|
||
if {![using_hla]} {
|
||
# if srst is not fitted use SYSRESETREQ to
|
||
# perform a soft reset
|
||
cortex_m reset_config sysresetreq
|
||
}
|
||
|
||
set _FLASHNAME $_CHIPNAME.flash
|
||
flash bank $_FLASHNAME at91samd 0x00000000 0 1 1 $_TARGETNAME
|